Left hand Domino type switchgear with high and low beam, pass, indicator and horn switches. Same style switch as ELA01738

On most bikes this will not plug directly into the wiring loom, you will need to match the wires to your loom. An indication of wire colours is supplied with this switchgear. Supplied with 9 pin block connector. NB does not have lights off - park - on function, you need this to be on your RH switch (e.g. ELA01729 ) or run lights always on

 This part is available by special order, request a quote

Domino left hand switchgear with lights on - park - off, high and low beam, pass, indicator and horn switches. Same style switch as ELA01738.

Already wired in to 9 pin block connector (you may need to alter the wiring on your bike to correspond to this block connector). Originally fitted as standard to early V11 Sport models. See the wiring diagram on our technical documents page for help installing this switchgear. See Greg Bender's website for a custom sub-loom that enables easy fitting of this part to models previously fitted with LEGO style swithgear

 This part is due back in stock soon, call 01484 841395 to reserve yours

 01738030 GU01738030 01 73 80 30
 0173 8030 0173.8030 01.73.80.30

Old type 4 pin starter relay in metal case. Note that this has two large terminals and two smaller ones, depending on model you may need to fit wider spade connectors to fit this relay. See ELA10003 for large female spade connectors

 This part is due back in stock soon, call 01484 841395 to reserve yours

 12732500 GU12732500 12 73 25 00
 1273 2500 1273.2500 12.73.25.00

Rectifier / diode board for Bosch charging systems. High quaility replacement part sourced from Germany

See our Bosch fault finder page for help diagnosing problems on your Bosch charging system.

 This part is due back in stock soon, call 01484 841395 to reserve yours

17704300-z 17704300 GU17704300 17 70 43 00
 1770 4300 1770.4300 17.70.43.00

3 pin plastic connector for headlight bulb spade connections

No longer available from Guzzi

 Sorry, this part is no longer available.

 17740364 GU17740364 17 74 03 64
 1774 0364 1774.0364 17.74.03.64

Alternator stator for Bosch charging systems, this does not include the plate and brush holders

To fit this you will need to solder in the three wires from the windings. Replacement rotors and brushes also available. See ELA00503 for a complete higher output upgrade for your charging system

 This part is available by special order, request a quote

 17712400 GU17712400 17 71 24 00
 1771 2400 1771.2400 17.71.24.00

Brush holder for Bosch alternator stator

Also known as Guzzi ref. 17712454, 14712452

Includes brushes. See ELA17453

 This part is due back in stock soon, call 01484 841395 to reserve yours

 17712452 GU17712452 17 71 24 52
 1771 2452 1771.2452 17.71.24.52

Replacement alternator brushes or brush kit for Bosch alternators

Also known as Guzzi ref 17712453

 This part is due back in stock soon, call 01484 841395 to reserve yours

14712453-z 14712453 GU14712453 14 71 24 53
 1471 2453 1471.2453 14.71.24.53

Also fits Benelli 900 Sei (Series 2)

Kit containing two replacement 60cm silicon HT leads, lead ends and 90° plug caps. The leads are suppied as a single double length lead so you can cut it into two leads of the exact required length. Includes crimp on lead ends for standard big twin 12v round coils

Suitable for most models with coils under the tank where the HT lead is not moulded into the ignition coil. We recommend checking what type of plug cap you have and measuring your existing cable run to check this part will fit

 This part is due back in stock soon, call 01484 841395 to reserve yours

Motoplat ignition unit for one cylinder (2 required per bike)

Also known as Guzzi ref. 23721493, 27721435, 23721491, 23721490, 27721435

 This part is available by special order, request a quote

 23721494 GU23721494 23 72 14 94
 2372 1494 2372.1494 23.72.14.94